Components
Page 2 No results were found for the filter!
steinert® (Deutschland)
Standard Boom for free-standing tool support stands 2 x support feet for additional stabilisation of the free-standing tool rest stand
€137.00 *
steinert® (Deutschland)
Tool Rest 400mm inc. Second Lower Part for the Steinert® piccolo lathe Shank diameter 2 x 25mm For centre height 150mm or 180mm Including second lower part
€265.00 *
steinert® (Deutschland)
Reducing Sleeve 40 to 25.4mm for VB36 Bennison adapter The sleeve makes it possible to change the diameter of the drive bearing bore from 40 mm to 24.4 mm so that a pin with a smaller diameter can be used for mounting .
€39.00 *
steinert® (Deutschland)
Reducing Sleeve for Tool Rest Shafts from Ø 40mm to Ø 30mm Reducing sleeve for tool rest shafts from Ø 40mm to Ø 30mm. tool rests or tool rests with a shaft diameter of 30mm can be used in tool rest bases with a 40mm holder.
€74.99 *
steinert® (Deutschland)
Tool Rest Lower Part, Shaft 30mm for centre height 200-250mm 30mm shaft Without support rail
€365.00 *
steinert® (Deutschland)
Shaft Collar Inside Ø 25, 30, 32, 40 or 60 mm Please select the desired inner Ø! The adjusting ring can be used to set the desired working height of the tool rest. It thus serves to make work easier. These set collars are equipped with a grub screw with a conical dome. This prevents marks in the shaft, which can occur with pointed grub screws.
From €3.15 *
Killinger®/steinert® (Taiwan/Deutschland)
Tool rest 350 mm shaft 30 mm, center height 180-200 mm for center height 180-200 mm (depends on heigt and geometry of tool rest basis) shaft diameter 30 mm suitable for Killinger KM 1400 SE, 1450 SE and 1500 SE lathes
€69.00 *
Sorby (England)
Shank for Tool Rest system from Robert Sorby Shank Ø: 16, 20, 25, 25.4 or 30 mm Shank for Robert Sorby tool rest system Shank for the Robert Sorby tool rest system. We offer the tenon in different versions. Length and diameter are adapted so that the most common lathes can be equipped with it. Compatible with all tool rests of this series. Standardized M12 x 1.25 mm thread. The length specifications refer exclusively to the height of the tang without...
From €17.90 *
Sorby (England)
Modular Tool Rest System, Robert Sorby different sizes and shapes Please select the desired variant! There is a choice of different hand rests for the tool rest system from Robert Sorby. The traditional company from the heart of England convinces with this product with quality materials in combination with high quality workmanship. The rests are made of specially hardened steel and thus ensure a well-sliding, resistance-free surface. Due...
From €24.40 *
hapfo®/steinert® (Deutschland)
Tool Rest hapfo 180, 275 or 425 mm Please select the desired length! Tool rest upper part suitable for woodturning lathe hapfo Performer with 402 cm center height in combination hapfo tool rest lower part good gliding of the tool due to high quality grey cast iron convex for optimal adaptation to the tool angle hollow shaped for better accessibility 30 mm shank diameter, approx. 150 mm shank length
From €138.22 *
Killinger®/steinert® (Taiwan/Deutschland)
Lower part Tool Rest cast iron, shank 30 mm, long for center height 260 - 300 mm Hand rest lower part made of cast iron. Suitable for lathes with cheek distance 45 mm and a center height of 180 mm. The holder for the shaft of the hand rest has a diameter of 30 mm. The hand rest shown in the picture is not included. Special production for other lathe makes possible on request. The lower part is completely assembled and can be placed directly on the lathe.
€269.00 *
Killinger®/steinert® (Taiwan/Deutschland)
Raiser Tool Rest, pin 120 mm Shank Ø 30mm Peg for extending the tool rest by 120 mm on the lathe. The extension spigot fits all bases with 30 mm receptacle. Suitable for holding tool rests with diameter 30 mm (depth of the hole: 105 mm). Custom made according to customer's request: Upon customer's request, we can adjust the shank Ø and height. This is associated with additional costs. If you need a component to be...
€48.80 *
Killinger®/steinert® (Taiwan/Deutschland)
Raiser Tool Rest , pin 280 mm Extension spigot for tool rest by 230 mm on the lathe. The spigot fits all bases with 30 mm shank mount. For tool rests with shank - diameter 30 mm. Special production according to customer's request: On customer's request we can adjust the shank Ø and height. This is connected with additional costs. If you need a component to be adapted to your existing tool base, please...
€71.40 *
Sale This item is excluded from exchange and return.
Content 1 Stück
€9.00 * €22.00 *
You have last looked at the following articles: