Special offer at the start of the month

shaft 30 mm, center height 180-200 mm For center height 180-200 mm (depends on heigt and geometry of tool rest basis) shaft diameter 30 mm Suitable for Killinger KM 1400 SE, 1450 SE and 1500 SE lathes

shaft 30 mm, center height 280-300 mm for center height 280-300 mm (depends on heigt and geometry of tool rest basis) shaft diameter 30 mm suitable for Killinger KM 3100 SE

shaft 30 mm, center height 180-200 mm for center height 180-200 mm (depends on heigt and geometry of tool rest basis) shaft diameter 30 mm suitable for Killinger KM 1400 SE, 1450 SE and 1500 SE lathes

M33 x 3.5 thread For screwing on blanks, with two pitch circles (see drawing) for spindle thread M33 x 3.5. This faceplate has a EURO ASR drain safety groove. The lathe shaft must also have a standardised groove so that the face plate can be secured with a locking ring.

M33 x 3.5 face plate with balancing washers Face plate with adjustable balancing discs for spindle thread M33 x 3.5 The hapfo-BALANCER is a faceplate with integrated, adjustable balancing discs, which enables significantly higher speeds, especially when processing unbalanced wet wood blanks or eccentrically clamped workpieces. It is also suitable for smaller machines, which otherwise only allow minimal speeds without...

different hardnesses Foam sanding pad / sanding pad with Velcro to hold sanding discs. Ideal for sanding wooden bowls and other concave and convex surfaces. The sanding pads are taken up in a hand drill. When used on the lathe, this results in a second grinding direction in relation to the rotation of the workpiece, which results in a significantly better grinding quality than with simple hand...

Grain 80 to 600 with VELCRO® fleece Please select the desired grit size! Abrasive discs made of linen with Velcro fleece to attach to the abrasive tools or to the spacer. Abrasive pad or adapter are not included.

medium hardness Foam sanding pad / sanding pad with Velcro to hold sanding discs. Ideal for sanding wooden bowls and other concave and convex surfaces. The sanding pads are taken up in a hand drill. When used on the lathe, this results in a second grinding direction in relation to the rotation of the workpiece, which results in a significantly better grinding quality than with simple hand...

Grain 80 to 600 with VELCRO® Velcro fleece Please select the desired grit size! Sanding discs made of linen with Velcro fleece for fastening on the sanding tools or on the intermediate piece. Abrasive pad or spacer are not included.

for Killinger® KM 1400 SE, 1450 SE, 1500 SE, 3000 SE or 3100 SE lathes Choose the outside turning fixture for your Killinger woodturning lathe! KM1400SE wood lathe: The device is attached to the side of the bench bed of the machine. Then turn and lock the headstock of the lathe! Outside turning on the KM1400SE allows you to machine shell diameters up to 620 mm. KM1450SE, KM1500SE and KM3100SE woodturning machine: The fixture is placed and...

For lathes Killinger KM 1450 SE and KM 1500 SE Steady rest for mounting on the Killinger KM 1450 SE and KM 1500 SE lathe. for center height 200 mm heavy steel construction, wall thickness 20 mm low vibration, no aluminum Clamping diameter min.7.5 mm / max. 110 mm rollers D = 40 mm

2MT Recording MT2 Size of the MT morse taper: largest diameter in mm smallest diameter in mm MT2 17.98 14.53

6-Prong, 2MT with extraction nut Size of the MT morse taper: largest diameter in mm smallest diameter in mm 2MT 17.98 14.53

6-Prong, 2MT with extraction nut Size of the MT morse taper: largest diameter in mm smallest diameter in mm 2MT 17.98 14.53

Width: 17mm; Length: 235mm The tools for making instruments are forged from a high-alloy carbon steel. The blades are finely ground and razor sharp. Plum wood handles with brass ferrules. 1. general information about pfeil tools, edge No. names and correct sharpening of tools (PDF File 0.2 MB) 2. Download the pfeil general catalog (PDF file 4.5 MB)

Width: 12mm; Length: 205mm The tools for making instruments are forged from a high-alloy carbon steel. The blades are finely ground and razor sharp. Plum wood handles with brass ferrules. 1. general information about pfeil tools, edge No. names and correct sharpening of tools (PDF File 0.2 MB) 2. Download the pfeil general catalog (PDF file 4.5 MB)

without booklet Blade made of HSS for carving knives, without handle, forged Blade length 50mm, total length with tang 90mm In contrast to the other tools from the Pfeil company, these carving blades only have a basic bevel. Information about the new HSS carving blades: The high-speed steel HSS (High Speed Steel) has a high proportion of molybdenum (5%) and tungsten (6%) compared to...

Adapter for clamping elements (chucks, face plates, etc.) with internal thread 1" x 8 tpi to enable use on a lathe with spindle thread M33 x 3.5. Overall length: 78mm, of which 30mm external thread including centring collar.

Adapter to be able to use clamping elements (chucks, face plates, etc.) with internal thread M33 x 3.5 on a lathe with spindle thread 1" x 8 tpi . External thread: M33 x 3.5 incl. centring collar Ø 34 mm h7 (according to DIN800) Internal thread: 1" x 8 tpi incl. centring collar Ø 27 mm H7 / length 6 mm Total length: 42 mm, including 30 mm external thread Outer diameter on...

Adapter for clamping elements (chucks, face plates, etc.) with internal threads M33 x 3.5 for use on a lathe with spindle thread 3/4" x 16 tpi.

Adapter for clamping elements (chucks, face plates, etc.) with internal threads M33 x 3.5 for use on a lathe with spindle thread M18 x 2.5. Total length: 50 mm

for individual customization For machining an internal thread in order to be able to use clamping elements (chucks, face plates, etc.) with a thread that differs from the lathe thread (M33 x 3.5). The internal thread must be cut on a metal lathe or produced by a metal specialist. Core drill Ø: 8 mm Total length: 50 mm Length of the rear part: 20 mm Diameter of the rear part: 49 mm

for spindle thread M18 x 2.5 Thread outside: 1" x 8tpi Inner thread: M18 x 2.5 Suitable for mini 4-jaw chucks

Adapter for clamping elements (chucks, face plates, etc.) with internal threads M33 x 3.5 for use on a lathe with spindle thread M18 x 1.5. Total length 50 mm