Components

for free-standing tool support stands 2 x support feet for additional stabilisation of the free-standing tool rest stand

steinert® lathes Adaptation to third-party products is possible. To enable this we need detailed information and drawings of the bench bed cross-section and centre height. Consultation is necessary when ordering. Under certain circumstances, there may be an additional price for adjustments.

for the Steinert® piccolo lathe Shank diameter 2 x 25mm For centre height 150mm or 180mm Including second lower part

from Ø 40 mm to Ø 25.4 mm With the reducing sleeve, hand rests and tool rests with a 25.4 mm (1 inch) shank diameter can be used in hand rest bases with a Ø 40 mm mount. Inner Ø: 25.4 mm / 1" Outer Ø: 40 mm Length: 126 mm

from Ø 40 mm to Ø 30 mm With the reducing sleeve, hand rests and tool rests with a 30 mm shank diameter can be used in hand rest bases with a Ø 40 mm mount. The sleeve has a collar at the top to prevent it from sinking into the 40 mm hole. Inner Ø: 30 mm Outer Ø: 40 mm Length under collar: 80 mm Length with collar: 91 mm

for centre height 200-250mm 30mm shaft Without support rail

Inside Ø 25, 30, 32, 40 or 60 mm Please select the desired inner Ø! The adjusting ring can be used to set the desired working height of the tool rest. It thus serves to make work easier. These set collars are equipped with a grub screw with a conical dome. This prevents marks in the shaft, which can occur with pointed grub screws.

shaft 30 mm, center height 180-200 mm for center height 180-200 mm (depends on heigt and geometry of tool rest basis) shaft diameter 30 mm suitable for Killinger KM 1400 SE, 1450 SE and 1500 SE lathes

Shank Ø: 16, 20, 25, 25.4 or 30 mm Shank for Robert Sorby tool rest system Shank for the Robert Sorby tool rest system. We offer the tenon in different versions. Length and diameter are adapted so that the most common lathes can be equipped with it. Compatible with all tool rests of this series. Standardized M12 x 1.25 mm thread. The length specifications refer exclusively to the height of the tang without...

different sizes and shapes Please select the desired variant! There is a choice of different hand rests for the tool rest system from Robert Sorby. The traditional company from the heart of England convinces with this product with quality materials in combination with high quality workmanship. The rests are made of specially hardened steel and thus ensure a well-sliding, resistance-free surface. Due...

Please select the desired length! Tool rest upper part suitable for woodturning lathe hapfo Performer with 402 cm center height in combination hapfo tool rest lower part good gliding of the tool due to high quality grey cast iron convex for optimal adaptation to the tool angle hollow shaped for better accessibility 30 mm shank diameter, approx. 150 mm shank length

Shank Ø 30mm Peg for extending the tool rest by 120 mm on the lathe. The extension spigot fits all bases with 30 mm receptacle. Suitable for holding tool rests with diameter 30 mm (depth of the hole: 105 mm). Custom made according to customer's request: Upon customer's request, we can adjust the shank Ø and height. This is associated with additional costs. If you need a component to be...

Schaft-Ø 30 mm Extension spigot for tool rest by 230 mm on the lathe. The spigot fits all bases with 30 mm shank mount. For tool rests with shank - diameter 30 mm. Special production according to customer's request: On customer's request we can adjust the shank Ø and height. This is connected with additional costs. If you need a component to be adapted to your existing tool base, please...

Sale This item is excluded from exchange and return.