Tool supports
Page 2 No results were found for the filter!

Killinger®/steinert® (Taiwan/Deutschland)
Tool Rest Extension by 280mm Schaft-Ø 30 mm Extension spigot for tool rest by 230 mm on the lathe. The spigot fits all bases with 30 mm shank mount. For tool rests with shank - diameter 30 mm. Special production according to customer's request: On customer's request we can adjust the shank Ø and height. This is connected with additional costs. If you need a component to be adapted to your existing tool base, please...
€71.40 *

steinert® (Deutschland)
Melvyn Firmager Guide Pin for VB36 tool rest All VB36 tool supports are provided with threaded holes. This guide pin can be screwed horizontally into the threaded hole. It is very helpful for certain work to enable you to guide the tool more cleanly and precisely.
€12.00 *

steinert® (Deutschland)
Deep Hollowing Rest Shank-Ø: 30 or 40 mm When turning hollow forms, there is often a considerable overhang of the tool over the tool rest resulting in unfavorable leverage. This curved tool rest can be positioned so that it protrudes into the hollow mold. There are holes on the top of the curved tool rest rail, these serve to accommodate an optionally available fork guide or a guide pin. A bar lying horizontally...
From €374.00 *

steinert® (Deutschland)
Curved Tool Rest Shank Ø: 16, 20 mm or 1" When turning hollow forms, there is often a considerable overhang of the tool over the tool support which results in unfavourable leverage. This curved tool rest can be positioned so that it protrudes into the hollow mold. There are holes on the top of the curved tool support rail; these serve to accommodate an optionally available fork guide or a guide pin. A bar lying...
€175.00 *

steinert® (Deutschland)
Forked Rest for Deep Hollowing Rest VB36 An accessory for the curved tool support rail of the VB36 Serves to guide the tool in deeply turned workpieces
€29.00 *

steinert® (Deutschland)
Short Fulcrum Pin for Deep Hollowing Rest VB36 An accessory for the curved tool support rail of the VB36 Serves to guide the tool in deeply turned workpieces
€12.00 *

steinert® (Deutschland)
Reducing sleeve for tool rests from Ø 40 mm to Ø 30 mm With the reducing sleeve, hand rests and tool rests with a 30 mm shank diameter can be used in hand rest bases with a Ø 40 mm mount. The sleeve has a collar at the top to prevent it from sinking into the 40 mm hole. Inner Ø: 30 mm Outer Ø: 40 mm Length under collar: 80 mm Length with collar: 91 mm
€74.99 *

steinert® (Deutschland)
Reducing sleeve for tool rests from Ø 40 mm to Ø 25.4 mm With the reducing sleeve, hand rests and tool rests with a 25.4 mm (1 inch) shank diameter can be used in hand rest bases with a Ø 40 mm mount. Inner Ø: 25.4 mm / 1" Outer Ø: 40 mm Length: 126 mm
€39.00 *

steinert® (Deutschland)
Free Standing Tool Rest for VB36 lathe If workpieces with a diameter of more than 915 mm (largest possible diameter above cantilever rail) are to be machined on the VB36, this free-standing tool rest stand must be used. It is suitable for all tool supports of the VB36. The diameter of the mount is 40mm The head lathe VB36 was manufactured in 2 different heights in the past - "L" (low) and "H" (high). Since 2019,...
€620.00 *

steinert® (Deutschland)
Standard Boom for free-standing tool support stands 2 x support feet for additional stabilisation of the free-standing tool rest stand
€137.00 *
You have last looked at the following articles: