Tool supports
No results were found for the filter!

steinert® (Deutschland)
Tool rest 180 mm Shank Ø 30/40mm Tool rest 180 mm with Shank Ø 30 / 40 mm
€185.00 *

steinert® (Deutschland)
Tool rest 275 mm Shank Ø 30/40mm Tool rest 275 mm with Shank Ø 30 / 40 mm
€205.00 *

steinert® (Deutschland)
Tool rest 425 mm Shank Ø 30/40mm Tool rest 425 mm with Shank Ø 30 / 40 mm
€225.00 *

Killinger®/steinert® (Taiwan/Deutschland)
Tool Rest lower part, cast iron, shank 30 mm For center height 180 - 220 mm Bottom part tool rest made of cast iron, for woodturning machines with center height 180 mm to 220 mm. The lower part is suitable for all tool rests with shank diameter 30 mm. Please measure the distance between the cheeks on your lathe beforehand and select the appropriate variant. The lower part is fully assembled and ready for use. You only have to attach the clamping...
€144.90 *

Killinger®/steinert® (Taiwan/Deutschland)
Tool Rest Extension by 120mm Shank Ø 30mm Peg for extending the tool rest by 120 mm on the lathe. The extension spigot fits all bases with 30 mm receptacle. Suitable for holding tool rests with diameter 30 mm (depth of the hole: 105 mm). Custom made according to customer's request: Upon customer's request, we can adjust the shank Ø and height. This is associated with additional costs. If you need a component to be...
€48.80 *

steinert® (Deutschland)
Tool Rest Lower Part Heavy, Shaft 40mm for centre height 250-300mm Large version Shaft 40mm Support Rail not included
€385.00 *

hapfo®/steinert® (Deutschland)
Tool Rest hapfo 180, 275 or 425 mm Please select the desired length! Tool rest upper part suitable for woodturning lathe hapfo Performer with 402 cm center height in combination hapfo tool rest lower part good gliding of the tool due to high quality grey cast iron convex for optimal adaptation to the tool angle hollow shaped for better accessibility 30 mm shank diameter, approx. 150 mm shank length
From €138.22 *

steinert® (Deutschland)
Tool Rest 120mm, Shaft 25mm for the Steinert® piccolo lathe and other makes For centre heights 150mm to 180mm Shank diameter 25mm
€59.00 *

steinert® (Deutschland)
Tool Rest 160mm, Shaft 25mm for the Steinert® piccolo lathe and other makes For centre heights 150mm to 180mm Shank diameter 25mm This tool rest is part of the standard equipment of the steinert® piccolo.
€59.00 *

steinert® (Deutschland)
Tool Rest Lower Part, Shaft 30mm for centre height 200-250mm 30mm shaft Without support rail
€365.00 *

Killinger®/steinert® (Taiwan/Deutschland)
Tool rest 170 mm shaft 30 mm, center height 180-200 mm For center height 180-200 mm (depends on heigt and geometry of tool rest basis) shaft diameter 30 mm Suitable for Killinger KM 1400 SE, 1450 SE and 1500 SE lathes
€59.00 *

steinert® (Deutschland)
Tool Rest 240mm, Shaft 25mm for the Steinert® piccolo lathe and other makes For centre heights 150mm to 180mm Shank diameter 25mm
€59.00 *

Axminster (England)
Tool rest with hardened round steel different lengths Standard tool rest with welded-on hardened steel rod. This ensures that your tool glides effortlessly while turning and that there are no notches or damage to the sliding face. The concave shape of the support ensures a better grip and allows the turning tool to be controlled better. Internal thread tool rest: M12 x 1.25mm Centering hole: 15.5mm Total height: 55mm Compatible...
From €19.80 *

Sorby (England)
Modular Tool Rest System, Robert Sorby different sizes and shapes Please select the desired variant! There is a choice of different hand rests for the tool rest system from Robert Sorby. The traditional company from the heart of England convinces with this product with quality materials in combination with high quality workmanship. The rests are made of specially hardened steel and thus ensure a well-sliding, resistance-free surface. Due...
From €24.40 *

Sorby (England)
Shank for Tool Rest system from Robert Sorby Shank Ø: 16, 20, 25, 25.4 or 30 mm Shank for Robert Sorby tool rest system Shank for the Robert Sorby tool rest system. We offer the tenon in different versions. Length and diameter are adapted so that the most common lathes can be equipped with it. Compatible with all tool rests of this series. Standardized M12 x 1.25 mm thread. The length specifications refer exclusively to the height of the tang without...
From €17.90 *

Killinger®/steinert® (Taiwan/Deutschland)
Tool rest 350 mm shaft 30 mm, center height 180-200 mm for center height 180-200 mm (depends on heigt and geometry of tool rest basis) shaft diameter 30 mm suitable for Killinger KM 1400 SE, 1450 SE and 1500 SE lathes
€69.00 *

Killinger®/steinert® (Taiwan/Deutschland)
Tool Rest 350 mm shaft 30 mm, center height 280-300 mm for center height 280-300 mm (depends on heigt and geometry of tool rest basis) shaft diameter 30 mm suitable for Killinger KM 3100 SE
€99.00 *

steinert® (Deutschland)
Tool rest curved, Ø 150 mm, adjustable Shank Ø 30 / 40mm Tool rest curved, Ø 150 mm, adjustable with shank Ø 30 / 40 mm
From €129.50 *

steinert® (Deutschland)
Curved Tool Rest for the Steinert® piccolo lathe and other makes For centre heights 150mm to 180mm Shank diameter 25mm
€85.00 *

steinert® (Deutschland)
Shaft Collar Inside Ø 25, 30, 32, 40 or 60 mm Please select the desired inner Ø! The adjusting ring can be used to set the desired working height of the tool rest. It thus serves to make work easier. These set collars are equipped with a grub screw with a conical dome. This prevents marks in the shaft, which can occur with pointed grub screws.
From €3.15 *

steinert® (Deutschland)
Tool rest 1000 mm incl. second lower part 2 x shaft Ø 30 or 40mm For long turned parts. Available with 2 x shank Ø 30 or 2 x shank Ø 40 mm. Please select.
€640.00 *

steinert® (Deutschland)
Tool Rest 400mm inc. Second Lower Part for the Steinert® piccolo lathe Shank diameter 2 x 25mm For centre height 150mm or 180mm Including second lower part
€265.00 *

steinert® (Deutschland)
Tool Rest rail 130, 200, 300 or 400mm without shaft Very stable tool rest made of vibration-damping grey cast iron. The tool rest is provided with an M16 hole into which the shaft for the tool rest is screwed (available seperately) The height of the tool rest rail is 110mm. Before ordering, please check whether this size fits your machine. Note that the upper edge of the rail should be at least 10mm below the axis of...
From €105.50 *

steinert® (Deutschland)
Shank for Tool Rest Shank Ø: 30 or 40mm For use on the VBT tool rest rails without a shaft. If the palm rest is used on one machine, the shaft can be glued in. If the tool rest is to be used on multiple machines with different tool rest shank diameters, the shank is not glued and can be changed. Thread: M16 Thread length: 23mm
From €24.90 *
You have last looked at the following articles: