Components
No results were found for the filter!

for centre height 250-300mm Large version Shaft 40mm Support Rail not included
€385.00 *

as button or latching These high-quality foot switches from the German manufacturer Bernstein AG have proven themselves for many years as an additional switching element on the VB36 head lathe. In addition to the practical benefit that both hands remain free when the machine is switched off and on, a foot switch makes a significant contribution to safety when using the lathe. The accident...
From €155.00 *

for head lathe VB36 If workpieces with a diameter of more than 915 mm (largest possible diameter above cantilever rail) are to be machined on the VB36, this free-standing tool support stand must be used. It is suitable for all tool supports of the VB36. The diameter of the mount is 40mm The head lathe VB36 was manufactured in 2 different heights in the past - "L" (low) and "H" (high). Since...
€559.00 *

Shank Ø: 1 ", 16, 20 or 30mm When turning hollow forms, there is often a considerable overhang of the tool over the tool support which results in unfavourable leverage. This curved tool rest can be positioned so that it protrudes into the hollow mold. There are holes on the top of the curved tool support rail; these serve to accommodate an optionally available fork guide or a guide pin. A bar lying...
From €135.00 *

for Bowl lathe VB36 Shank Ø: 40mm When turning hollow forms, there is often a considerable overhang of the tool over the tool support resulting in unfavorable leverage. This curved tool rest can be positioned so that it protrudes into the hollow mold. There are holes on the top of the curved tool support rail, these serve to accommodate an optionally available fork guide or a guide pin. A bar...
€319.00 *

2 x shaft Ø 30 or 40mm For long turned parts. Available with 2 x shafts Ø 30 or 2 x shafts Ø 40mm. Please select.
€640.00 *

without shaft Very stable hand rest made of vibration-damping grey cast iron. The hand rest is provided with an M16 hole into which the shaft for the tool rest is screwed (available seperately) The height of the tool support rail is 110mm. Before ordering, please check whether this size fits your machine. Note that the upper edge of the rail should be at least 10mm below the axis of...
From €61.50 *

Shank Ø: 30 or 40mm For use on the VBT tool support rails without a shaft. If the palm rest is used on one machine, the shaft can be glued in. If the hand rest is to be used on multiple machines with different tool rest shank diameters, the shank is not glued and can be changed. Thread: M16 Thread length: 23mm
From €24.90 *

for the Steinert® piccolo lathe and other makes For centre heights 150mm to 180mm Shank diameter 25mm
€59.00 *

for VB36 tool supports All VB36 tool supports are provided with threaded holes. This guide pin can be screwed horizontally into the threaded hole. It is very helpful for certain work to enable you to guide the tool more cleanly and precisely.
€12.00 *

for the Steinert® piccolo lathe and other makes For centre heights 150mm to 180mm Shank diameter 25mm
€85.00 *

for Deep Hollowing Rest VB36 An accessory for the curved tool support rail of the VB36 Serves to guide the tool in deeply turned workpieces
€29.00 *

for Deep Hollowing Rest VB36 An accessory for the curved tool support rail of the VB36 Serves to guide the tool in deeply turned workpieces
€12.00 *

for the Steinert® piccolo lathe and other makes For centre heights 150mm to 180mm Shank diameter 25mm This tool support is part of the standard equipment of the steinert® piccolo.
€59.00 *

for free-standing tool support stands 2 x support feet for additional stabilisation of the free-standing tool rest stand
€137.00 *

for the Steinert® piccolo lathe and other makes For centre heights 150mm to 180mm Shank diameter 25mm
€59.00 *

for the Steinert® piccolo lathe Shank diameter 2 x 25mm For centre height 150mm or 180mm Including second lower part
€265.00 *

from Ø 40mm to Ø 30mm Reducing sleeve for hand rest shafts from Ø 40mm to Ø 30mm. Hand rests or tool rests with a shaft diameter of 30mm can be used in hand rest bases with a 40mm holder.
€74.99 *
Viewed