steinert® VB36

for head lathe VB36 Set of two drive belts

Type TA45-ABCWFC00U2

Steel rail to extend the extra-long tool support to 1000mm

for free-standing tool support stands 2 x support feet for additional stabilisation of the free-standing tool rest stand

for free-standing tool support stands 2 x support feet for additional stabilisation of the free-standing tool rest stand

for VB36 built before 1996 The original version of the fine adjustment for the VB36 tool supports, was a bit stiff and unwieldy. With this retrofit sleeve, the machine can be equipped with today's Bennison adapter. Delivery including fastening screw and lock washer.

from Ø 40 mm to Ø 25.4 mm With the reducing sleeve, hand rests and tool rests with a 25.4 mm (1 inch) shank diameter can be used in hand rest bases with a Ø 40 mm mount. Inner Ø: 25.4 mm / 1" Outer Ø: 40 mm Length: 126 mm

for head lathe VB36 We recommend always replacing the rack and pinion shaft in pairs. In the past, different tooth spacings were installed, individual replacement could lead to problems.

for head lathe VB36 Pre-assembled version with handwheel. We recommend always replacing the rack and pinion shaft in pairs. In the past, different tooth spacings were installed, individual replacement could lead to problems.

for head lathe VB36 To assemble the handwheel, the shaft for the split pin must be drilled. We recommend always replacing the rack and pinion shaft in pairs. In the past, different tooth spacings were installed, individual replacement could lead to problems.

for head lathe VB36

Shank Ø 30/40mm Tool rest 180 mm with Shank Ø 30 / 40 mm

Shank Ø 30/40mm Tool rest 275 mm with Shank Ø 30 / 40 mm

Shank Ø 30/40mm Tool rest 425 mm with Shank Ø 30 / 40 mm

Shank Ø 30 / 40mm Tool rest curved, Ø 150 mm, adjustable with shank Ø 30 / 40 mm

Shank Ø: 30 or 40mm For use on the VBT tool rest rails without a shaft. If the palm rest is used on one machine, the shaft can be glued in. If the tool rest is to be used on multiple machines with different tool rest shank diameters, the shank is not glued and can be changed. Thread: M16 Thread length: 23mm

as button or latching These high-quality foot switches from the German manufacturer Bernstein AG have proven themselves for many years as an additional switching element on the VB36 head lathe. In addition to the practical benefit that both hands remain free when the machine is switched off and on, a foot switch makes a significant contribution to safety when using the lathe. The accident...

with base jaws Axminster or Vicmarc VM120 This TOS precision 4-jaw chuck is an extremely stable and precisely processed chuck with a long service life. It is supplied with base jaws for holding Axminster or Vicmarc 120 clamping jaws. It can therefore be used flexibly for a wide variety of applications. As an alternative to the base jaws for Axminster or Vicmarc 120 attachments, the chuck can also be used with...

with threaded flange (various threads) and base jaws for Axminster attachments With threaded flange and base jaws for Axminster attachments. Please select the desired spindle thread when ordering! The variant spindle mount M33 x 3.5 Euro ASR is equipped with the standardized groove for the use of drain protection shells. The lathe also requires this standardized groove in the spindle. Spindle threads other than those listed in the selection are...

for head lathe VB36 Fine grooved mat for placing under the machine frame of the VB36 Vibration dampening effect The head lathe VB36 must be screwed to the floor. This rubber mat is placed between the machine and the floor Dimensions: 545 x 610mm

Inside Ø 25, 30, 32, 40 or 60 mm Please select the desired inner Ø! The adjusting ring can be used to set the desired working height of the tool rest. It thus serves to make work easier. These set collars are equipped with a grub screw with a conical dome. This prevents marks in the shaft, which can occur with pointed grub screws.

for VB36 Bowl Turner Lathe (Rear Bearing) For VB36 rear / handwheel side. 2 x pieces are required for the rear bearing. On request, we can also provide instructions on how to change the bearing seals.

for VB36 Bowl Turner Lathe (Front Bearing) For VB36 front / bayonet side. 2 x pieces are required for the front bearing. On request, we can also provide instructions on how to change the bearing seals.

for VB36 Bowl Turner Lathe For VB36 bearings. 4 x pieces are required. On request, we can also provide instructions on how to change the bearing seals.