No results were found for the filter!
steinert® (Deutschland)
VB LUBE Special Lubricant for VB36 0.25 or 0.75ltr for VB36 Special oil mixture for the plain bearings of the VB36 Master Bowlturner Lathe.
Content 0.25 Liter (€41.60 * / 1 Liter)
From €10.40 *
steinert® (Deutschland)
Replacement drive belt (set of 2) for head lathe VB36 Set of two drive belts
€39.95 *
for head lathe VB36 Filled with special hot bearing grease to lubricate the VB36 thrust bearings.
€39.40 *
steinert® (Deutschland)
Toothed Rack for head lathe VB36 We recommend always replacing the rack and pinion shaft in pairs. In the past, different tooth spacings were installed, individual replacement could lead to problems.
€59.50 *
steinert® (Deutschland)
Pinion Shaft for head lathe VB36 To assemble the handwheel, the shaft for the split pin must be drilled. We recommend always replacing the rack and pinion shaft in pairs. In the past, different tooth spacings were installed, individual replacement could lead to problems.
€76.06 *
steinert® (Deutschland)
Handwheel and Pinion Shaft for head lathe VB36 Pre-assembled version with handwheel. We recommend always replacing the rack and pinion shaft in pairs. In the past, different tooth spacings were installed, individual replacement could lead to problems.
€104.70 *
steinert® (Deutschland)
Bennison Adapter Retrofit Sleeve for VB36 built before 1996 The original version of the fine adjustment for the VB36 tool supports, was a bit stiff and unwieldy. With this retrofit sleeve, the machine can be equipped with today's Bennison adapter. Delivery including fastening screw and lock washer.
€144.00 *
Bernstein (Deutschland)
Foot Switch with Protective Cover as button or latching These high-quality foot switches from the German manufacturer Bernstein AG have proven themselves for many years as an additional switching element on the VB36 head lathe. In addition to the practical benefit that both hands remain free when the machine is switched off and on, a foot switch makes a significant contribution to safety when using the lathe. The accident...
From €186.70 *
for head lathe VB36 Fine grooved mat for placing under the machine frame of the VB36 Vibration dampening effect The head lathe VB36 must be screwed to the floor. This rubber mat is placed between the machine and the floor Dimensions: 545 x 610mm
€22.20 *
steinert® (Deutschland)
Oil Seal Viton 50mm for VB36 Bowl Turner Lathe (Rear Bearing) For VB36 rear / handwheel side. 2 x pieces are required for the rear bearing. On request, we can also provide instructions on how to change the bearing seals.
€7.86 *
steinert® (Deutschland)
Oil Seal Viton 60mm for VB36 Bowl Turner Lathe (Front Bearing) For VB36 front / bayonet side. 2 x pieces are required for the front bearing. On request, we can also provide instructions on how to change the bearing seals.
€9.15 *
steinert® (Deutschland)
O-Ring Viton 70mm for VB36 Bowl Turner Lathe For VB36 bearings. 4 x pieces are required. On request, we can also provide instructions on how to change the bearing seals.
€2.35 *
steinert® (Deutschland)
Bronze Sliding Washer for Bowl Lathe VB36 For VB36 thrust bearings. 2 x pieces required. Ø outside: 83.5 mm Ø inside: 51.5 mm
€42.90 *
steinert® (Deutschland)
Brass oil cup for VB36 for bowlturner lathe VB36 Seal ring included.
€46.80 *
steinert® (Deutschland)
Motor VB36 2HP motor 2HP original design VB36 Shaft diameter: 24 mm Keyway width: 8 mm Hole spacing foot flange: 140 x 125 mm
€170.00 *
You have last looked at the following articles: